DI EGIDIO, GIANLUCA
DI EGIDIO, GIANLUCA
DIN - DIPARTIMENTO DI INGEGNERIA INDUSTRIALE
Ricercatori a tempo determinato
An analysis of the influence of heat treatments and surface finishing conditions on the high cycle fatigue behaviour of W360 hot work tool steel produced by Powder Bed Fusion – Laser Beam
2025 Zanni, M.; Di Egidio, G.; Tonelli, L.; Morri, A.; Ceschini, L.
Caratterizzazione di un rivestimento multistrato (Ni-P+DLC) applicato su componenti in lega PBF-LB AlSi10Mg costituiti da geometrie complesse e strutture reticolari
2025 Di Egidio, G.; Martini, C.; Morri, A.; Tonelli, L.; Ceschini, L.; Tocci, M.; Gelfi, M.; Pola, A.; Martucci, A.; Lombardi, M.
Electroless Ni-P + diamond-like carbon multilayer: Influence on tribological behaviour of AlSi10Mg produced by powder bed fusion - Laser beam
2025 Di Egidio, Gianluca; Martini, Carla; Ghassemali, Ehsan; Morri, Alessandro
Direct artificial aging of the PBF-LB AlSi10Mg alloy designed to enhance the trade-off between strength and residual stress relief
2024 Di Egidio, Gianluca; Tonelli, Lavinia; Zanni, Mattia; Carosi, Daniele; Morri, Alessandro; Ceschini, Lorella
Influenza dei difetti di solidificazione e della grafite degenerata sulle proprietà meccaniche statiche di getti di grande spessore in ghisa sferoidale ferritica EN-GJS-400-15
2024 DI EGIDIO, Gianluca; Ferro, Paolo; Morri, Alessandro
Dry sliding behavior of AlSi10Mg alloy produced by Laser-based Powder Bed Fusion: influence of heat treatment and microstructure
2023 Di Egidio, G.; Martini, C.; Borjesson, J.; Ghassemali, E.; Ceschini, L.; Morri, A.
High‐Temperature Behavior of the Heat‐Treated and Overaged AlSi10Mg Alloy Produced by Laser‐Based Powder Bed Fusion and Comparison with Conventional Al–Si–Mg‐Casting Alloys
2023 Di Egidio, Gianluca; Morri, Alessandro; Ceschini, Lorella; Tonelli, Lavinia
Influence of Anodizing by Electro-Chemical Oxidation on Fatigue and Wear Resistance of the EV31A-T6 Cast Magnesium Alloy
2023 Di Egidio G.; Tonelli L.; Morri A.; Boromei I.; Shashkov P.; Martini C.
Influence of Electroless Nickel—DLC (Diamond-like Carbon) Multilayer Coating on the Mechanical Performance of the Heat-Treated AlSi10Mg Alloy Produced by Powder Bed Fusion-Laser Beam
2023 Di Egidio, Gianluca; Martini, Carla; Ceschini, Lorella; Morri, Alessandro
Influence of Microstructure on Fracture Mechanisms of the Heat-Treated AlSi10Mg Alloy Produced by Laser-Based Powder Bed Fusion
2023 Di Egidio, Gianluca; Martini, Carla; Börjesson, Johan; Ghassemali, Ehsan; Ceschini, Lorella; Morri, Alessandro
Influence of Ni-P + DLC multilayer coatings on the tensile properties of the AlSi10Mg alloy produced by Laser-based Powder Bed Fusion
2023 Di Egidio, G.; Ceschini, L.; Martini, C.; Morri, A.
Mechanical and microstructural features of wire-and-arc additively manufactured carbon steel thick plates
2023 Laghi V.; Arrè L.; Tonelli L.; Di Egidio G.; Ceschini L.; Monzón I.; Laguía A.; Dieste J.A.; Palermo M.
On the Role of Microstructure and Defects in the Room and High-Temperature Tensile Behavior of the PBF-LB A357 (AlSi7Mg) Alloy in As-Built and Peak-Aged Conditions
2023 Tonelli L.; Liverani E.; Di Egidio G.; Fortunato A.; Morri A.; Ceschini L.
Room- and High-Temperature Fatigue Strength of the T5 and Rapid T6 Heat-Treated AlSi10Mg Alloy Produced by Laser-Based Powder Bed Fusion
2023 Di Egidio, Gianluca; Ceschini, Lorella; Morri, Alessandro; Zanni, Mattia
A Novel T6 Rapid Heat Treatment for AlSi10Mg Alloy Produced by Laser-Based Powder Bed Fusion: Comparison with T5 and Conventional T6 Heat Treatments
2022 Di Egidio, Gianluca; Ceschini, Lorella; Morri, Alessandro; Martini, Carla; Merlin, Mattia
Evaluation by nanoindentation of the influence of heat treatments and the consequent induced microstructure on the mechanical response of the heattreated L-PBF AlSi10Mg alloy
2022 DI EGIDIO, Gianluca
EVALUATION OF HIGH-TEMPERATURE TENSILE PROPERTIES OF HEAT-TREATED ALSI10MG ALLOY PRODUCED BY LASER-BASED POWDER BED FUSION
2022 Gianluca Di Egidio, Alessandro Morri, Lorella Ceschini,
Effetto del trattamento termico T6 su microstruttura e comportamento meccanico della lega AlSi10Mg prodotta mediante Selective Laser Melting: stato dell’arte
2021 Gianluca Di Egidio, Lorella Ceschini, Alessandro Morri