The WP2 of the Geotech H2020 project has the following objectives: - Develop (design, test and produce) Hollow Stem Augers (HSA) for the installation of the concentric spiral heat exchanger developed in WP3. - Develop (design, test and produce) the associated auxiliary equipment for the HSA, that will allow efficient and cost effective operation and installation of the concentric heat exchanger developed in the Geotech project. - Develop (design, test and produce) a drill rig platform that integrates the HSA and its auxiliary equipment in an operator friendly and production efficient tool. - Investigate and test the potential application of the drill rig and auger equipment for the installation of the concentric spiral heat exchanger in foundation applications. The deliverable 2.1. publication first of all provides a general overview of the current state of the Ground Source Heat Pump (GSHP) technology based on shallow closed loop heat exchanger application. In addition, the technical and legislative requirements for GSHP installation in a number of countries are reviewed, indicating that a certain level of market introduction and awareness of the technology is present. In addition, the potential future role of Ground Source Heat Pumps (GSHP) as a renewable technology is positioned in the light of the RES directive and the National renewable energy action (Nreap) plans. Secondly, the deliverable 2.1. evaluates the currently available drilling and installation methods that are in use for installing vertical closed loop heat exchangers. This is done to assert the suitability of the proposed Hollow Stem Auger (HSA) for the installation of shallow heat exchangers, specifically the concentric spiral heat exchanger developed in the Geotech project. A similar task is undertaken to evaluate the role of the HSA and the concentric spiral heat exchanger in installing thermally activated foundations. Thirdly, using the information from the previous evaluation and from practical experience, the requirements and prototype design of the HSA, the drill rig and the auxiliary equipment required to successfully install the concentric spiral heat exchanger are stated. The objective of this section of the deliverable is to develop outline guidance and performance specification for actual prototyping of components that will be used for evaluation in the following phases of production and testing. The deliverable 2.1. concludes: The current and future position of GSHP • As an energy savings technology using renewables, GSHP clearly has a future role in combination with either renewable energy production (wind, solar, biomass) or with conventional energy production. Furthermore GSHP can store thermal energy. • Evaluating the current drilling and installation technology for vertical closed loop heat exchangers indicate that a dry drilling technique such as HSA has a number of distinct advantages when compared to conventional drilling systems using air or water as a flushing medium. • In the foundation application the main gain of the HSA and drill rig development will be in the ease of installation of the concentric spiral heat exchanger, allowing thermal activation of foundations with only very limited extra cost when compared to a conventional foundations. The outline specifications for the HSA, drillrig and auxiliary equipment • Automated, operator friendly drilling process • Installation capability for different diameter (63 – 200 mm) spiral heat exchangers in all non consolidated formations to a maximum of 50 to 60 meters of depth. • Based on previous experience and a very limited data set it is concluded that the torque and RPM requirement for successful HSA application should be in the region of 8.000 – 12.000 Nm (torque) and 25-150 RPM. • Experience based requirements from the foundation application section of this report underwrite these requirements for the successful use of augers for micropiling. • Limited amounts of water used in drilling process, direct processing of drilling spoils
Deliverable 2.1 - GEOTeCH Project - Report on the evaluation of available information
TINTI, FRANCESCO;BORTOLOTTI, VILLIAM;BONDUA', STEFANO;BRUNO, ROBERTO
2016
Abstract
The WP2 of the Geotech H2020 project has the following objectives: - Develop (design, test and produce) Hollow Stem Augers (HSA) for the installation of the concentric spiral heat exchanger developed in WP3. - Develop (design, test and produce) the associated auxiliary equipment for the HSA, that will allow efficient and cost effective operation and installation of the concentric heat exchanger developed in the Geotech project. - Develop (design, test and produce) a drill rig platform that integrates the HSA and its auxiliary equipment in an operator friendly and production efficient tool. - Investigate and test the potential application of the drill rig and auger equipment for the installation of the concentric spiral heat exchanger in foundation applications. The deliverable 2.1. publication first of all provides a general overview of the current state of the Ground Source Heat Pump (GSHP) technology based on shallow closed loop heat exchanger application. In addition, the technical and legislative requirements for GSHP installation in a number of countries are reviewed, indicating that a certain level of market introduction and awareness of the technology is present. In addition, the potential future role of Ground Source Heat Pumps (GSHP) as a renewable technology is positioned in the light of the RES directive and the National renewable energy action (Nreap) plans. Secondly, the deliverable 2.1. evaluates the currently available drilling and installation methods that are in use for installing vertical closed loop heat exchangers. This is done to assert the suitability of the proposed Hollow Stem Auger (HSA) for the installation of shallow heat exchangers, specifically the concentric spiral heat exchanger developed in the Geotech project. A similar task is undertaken to evaluate the role of the HSA and the concentric spiral heat exchanger in installing thermally activated foundations. Thirdly, using the information from the previous evaluation and from practical experience, the requirements and prototype design of the HSA, the drill rig and the auxiliary equipment required to successfully install the concentric spiral heat exchanger are stated. The objective of this section of the deliverable is to develop outline guidance and performance specification for actual prototyping of components that will be used for evaluation in the following phases of production and testing. The deliverable 2.1. concludes: The current and future position of GSHP • As an energy savings technology using renewables, GSHP clearly has a future role in combination with either renewable energy production (wind, solar, biomass) or with conventional energy production. Furthermore GSHP can store thermal energy. • Evaluating the current drilling and installation technology for vertical closed loop heat exchangers indicate that a dry drilling technique such as HSA has a number of distinct advantages when compared to conventional drilling systems using air or water as a flushing medium. • In the foundation application the main gain of the HSA and drill rig development will be in the ease of installation of the concentric spiral heat exchanger, allowing thermal activation of foundations with only very limited extra cost when compared to a conventional foundations. The outline specifications for the HSA, drillrig and auxiliary equipment • Automated, operator friendly drilling process • Installation capability for different diameter (63 – 200 mm) spiral heat exchangers in all non consolidated formations to a maximum of 50 to 60 meters of depth. • Based on previous experience and a very limited data set it is concluded that the torque and RPM requirement for successful HSA application should be in the region of 8.000 – 12.000 Nm (torque) and 25-150 RPM. • Experience based requirements from the foundation application section of this report underwrite these requirements for the successful use of augers for micropiling. • Limited amounts of water used in drilling process, direct processing of drilling spoilsI documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.
